Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on seismic, drilling, and source rock analysis data, the petroleum geological characteristics and future exploration direction of the oil-rich sags in the Central and West African Rift System (CWARS) are discussed. The study shows that the Central African Rift System mainly develops high-quality lacustrine source rocks in the Lower Cretaceous, and the West African Rift System mainly develops high-quality terrigenous organic matter-rich marine source rocks in the Upper Cretaceous, and the two types of source rocks provide a material basis for the enrichment of oil and gas in the CWARS. Multiple sets of reservoir rocks including fractured basement and three sets of regional cap rocks in the Lower Cretaceous, the Upper Cretaceous, and the Paleogene are developed in the CWARS. Since the Late Mesozoic, due to the geodynamic factors including the dextral strike-slip movement of the Central African Shear Zone, the basins in different directions of the CWARS differ in terms of rifting stages, intervals of regional cap rocks, trap types and accumulation models. The NE-SW trending basins have mainly preserved one stage of rifting in the Early Cretaceous, with regional cap rocks developed in the Lower Cretaceous strata, forming traps of reverse anticlines, flower-shaped structures and basement buried hill, and two types of hydrocarbon accumulation models of "source and reservoir in the same formation, and accumulation inside source rocks" and "up-source and down-reservoir, and accumulation below source rocks". The NW-SE basins are characterized by multiple rifting stages superimposition, with the development of regional cap rocks in the Upper Cretaceous and Paleogene, forming traps of draping anticlines, faulted anticlines, antithetic fault blocks and the accumulation model of "down-source and up-reservoir, and accumulation above source rocks". The combination of reservoir and cap rocks inside source rocks of basins with multiple superimposed rifting stages, as well as the lithologic reservoirs and the shale oil inside source rocks of strong inversion basins are important fields for future exploration in basins of the CWARS.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the practice of oil and gas exploration in the Huizhou Sag of the Pearl River Mouth Basin, the geochemical indexes of source rocks were measured, the reservoir development morphology was restored, the rocks and minerals were characterized microscopically, the measured trap sealing indexes were compared, the biomarker compounds of crude oil were extracted, the genesis of condensate gas was identified, and the reservoir-forming conditions were examined. On this basis, the Paleogene Enping Formation in the Huizhou 26 subsag was systematically analyzed for the potential of oil and gas resources, the development characteristics of large-scale high-quality conglomerate reservoirs, the trapping effectiveness of faults, the hydrocarbon migration and accumulation model, and the formation conditions and exploration targets of large- and medium-sized glutenite-rich oil and gas fields. The research results were obtained in four aspects. First, the Paleogene Wenchang Formation in the Huizhou 26 subsag develops extensive and thick high-quality source rocks of semi-deep to deep lacustrine subfacies, which have typical hydrocarbon expulsion characteristics of "great oil generation in the early stage and huge gas expulsion in the late stage", providing a sufficient material basis for hydrocarbon accumulation in the Enping Formation. Second, under the joint control of the steep slope zone and transition zone of the fault within the sag, the large-scale near-source glutenite reservoirs are highly heterogeneous, with the development scale dominated hierarchically by three factors (favorable facies zone, particle component, and microfracture). The (subaqueous) distributary channels near the fault system, with equal grains, a low mud content (<5%), and a high content of feldspar composition, are conducive to the development of sweet spot reservoirs. Third, the strike-slip pressurization trap covered by stable lake flooding mudstone is a necessary condition for oil and gas preservation, and the NE and nearly EW faults obliquely to the principal stress have the best control on traps. Fourth, the spatiotemporal configuration of high-quality source rocks, fault transport/sealing, and glutenite reservoirs controls the degree of hydrocarbon enrichment. From top to bottom, three hydrocarbon accumulation units, i.e. low-fill zone, transition zone, and high-fill zone, are recognized. The main area of the channel in the nearly pressurized source-connecting fault zone is favorable for large-scale hydrocarbon enrichment. The research results suggest a new direction for the exploration of large-scale glutenite-rich reservoirs in the Enping Formation of the Pearl River Mouth Basin, and present a major breakthrough in oil and gas exploration.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the global basement reservoir database and the dissection of basement reservoirs in China, the characteristics of hydrocarbon accumulation in basement reservoirs are analyzed, and the favorable conditions for hydrocarbon accumulation in deep basement reservoirs are investigated to highlight the exploration targets. The discovered basement reservoirs worldwide are mainly buried in the Archean and Precambrian granitic and metamorphic formations with depths less than 4500 m, and the relatively large reservoirs have been found in rift, back-arc and foreland basins in tectonic active zones of the Meso-Cenozoic plates. The hydrocarbon accumulation in basement reservoirs exhibits the characteristics in three aspects. First, the porous-fractured reservoirs with low porosity and ultra-low permeability are dominant, where extensive hydrocarbon accumulation occurred during the weathering denudation and later tectonic reworking of the basin basement. High resistance to compaction allows the physical properties of these highly heterogeneous reservoirs to be independent of the buried depth. Second, the hydrocarbons were sourced from the formations outside the basement. The source-reservoir assemblages are divided into contacted source rock-basement and separated source rock-basement patterns. Third, the abnormal high pressure in the source rock and the normal-low pressure in the basement reservoirs cause a large pressure difference between the source rock and the reservoirs, which is conducive to the pumping effect of hydrocarbons in the deep basement. The deep basement prospects are mainly evaluated by the factors such as tectonic activity of basement, source-reservoir combination, development of large deep faults (especially strike-slip faults), and regional seals. The Precambrian crystalline basements at the margin of the intracontinental rifts in cratonic basins, as well as the Paleozoic folded basements and the Meso-Cenozoic fault-block basements adjacent to the hydrocarbon generation depressions, have favorable conditions for hydrocarbon accumulation, and thus they are considered as the main targets for future exploration of deep basement reservoirs.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Through core observation, thin section identification, X-ray diffraction analysis, scanning electron microscopy, and low-temperature nitrogen adsorption and isothermal adsorption experiments, the lithology and pore characteristics of the Upper Carboniferous bauxite series in eastern Ordos Basin were analyzed to reveal the formation and evolution process of the bauxite reservoirs. A petrological nomenclature and classification scheme for bauxitic rocks based on three units (aluminum hydroxides, iron minerals and clay minerals) is proposed. It is found that bauxitic mudstone is in the form of dense massive and clastic structures, while the (clayey) bauxite is of dense massive, pisolite, oolite, porous soil and clastic structures. Both bauxitic mudstone and bauxite reservoirs develop dissolution pores, intercrystalline pores, and microfractures as the dominant gas storage space, with the porosity less than 10% and mesopores in dominance. The bauxite series in the North China Craton can be divided into five sections, i.e., ferrilite (Shanxi-style iron ore, section A), bauxitic mudstone (section B), bauxite (section C), bauxite mudstone (debris-containing, section D) and dark mudstone-coal section (section E). The burrow/funnel filling, lenticular, layered/massive bauxite deposits occur separately in the karst platforms, gentle slopes and low-lying areas. The karst platforms and gentle slopes are conducive to surface water leaching, with strong karstification, well-developed pores, large reservoir thickness and good physical properties, but poor strata continuity. The low-lying areas have poor physical properties but relatively continuous and stable reservoirs. The gas enrichment in bauxites is jointly controlled by source rock, reservoir rock and fractures. This recognition provides geological basis for the exploration and development of natural gas in the Upper Carboniferous in the study area and similar bauxite systems.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
The Ediacaran-Ordovician strata within three major marine basins (Tarim, Sichuan, and Ordos) in China are analyzed. Based on previous studies focusing on the characteristics of the Neoproterozoic-Cambrian strata within the three major basins (East Siberian, Oman, and Officer in Australia) overseas, the carbonate-evaporite assemblages in the target interval are divided into three types: intercalated carbonate and gypsum salt, interbedded carbonate and gypsum salt, and coexisted carbonate, gypsum salt and clastic rock. Moreover, the concept and definition of the carbonate-evaporite assemblage are clarified. The results indicate that the oil and gas in the carbonate-evaporite assemblage are originated from two types of source rocks: shale and argillaceous carbonate, and confirmed the capability of gypsum salt in the saline environment to drive the source rock hydrocarbon generation. The dolomite reservoirs are classified in two types: gypseous dolomite flat, and grain shoal & microbial mound. This study clarifies that the penecontemporaneous or epigenic leaching of atmospheric fresh water mainly controlled the large-scale development of reservoirs. Afterwards, burial dissolution transformed and reworked the reservoirs. The hydrocarbon accumulation in carbonate-evaporite assemblage can be categorized into eight sub-models under three models (sub-evaporite hydrocarbon accumulation, supra-evaporite hydrocarbon accumulation, and inter-evaporite hydrocarbon accumulation). As a result, the Cambrian strata in the Tazhong Uplift North Slope, Maigaiti Slope and Mazatag Front Uplift Zone of the Tarim Basin, the Cambrian strata in the eastern-southern area of the Sichuan Basin, and the inter-evaporite Ma-4 Member of Ordovician in the Ordos Basin, China, are defined as favorable targets for future exploration.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the study of the distribution of intra-platform shoals and the characteristics of dolomite reservoirs in the Middle Permian Qixia Formation in the Gaoshiti-Moxi area of the Sichuan Basin, SW China, the controlling factors of reservoir development were analyzed, and the formation model of “intra-platform shoal thin-layer dolomite reservoir” was established. The Qixia Formation is a regressive cycle from bottom to top, in which the first member (Qi1 Member) develops low-energy open sea microfacies, and the second member (Qi2 Member) evolves into intra-platform shoal and inter-shoal sea with decreases in sea level. The intra-platform shoal is mainly distributed near the top of two secondary shallowing cycles of the Qi2 Member. The most important reservoir rock of the Qixia Formation is thin-layer fractured-vuggy dolomite, followed by vuggy dolomite. The semi-filled saddle dolomite is common in fracture-vug, and intercrystalline pores and residual dissolution pores combined with fractures to form the effective pore-fracture network. Based on the coupling analysis of sedimentary and diagenesis characteristics, the reservoir formation model of “pre-depositional micro-paleogeomorphology controlling shoal, sedimentary shoal controlling dolomite, penecontemporaneous dolomite benefiting preservation of pores, and late hydrothermal action effectively improving reservoir quality” was systematically established. The “first-order high zone” micro-paleogeomorphology before the deposition of the Qixia Formation controlled the development of large area of intra-platform shoals in Gaoshiti area during the deposition of the Qi2 Member. Shoal facies is the basic condition of early dolomitization, and the distribution range of intra-platform shoal and dolomite reservoir is highly consistent. The grain limestone of shoal facies is transformed by two stages of dolomitization. The penecontemporaneous dolomitization is conducive to the preservation of primary pores and secondary dissolved pores. The burial hydrothermal fluid enters the early dolomite body along the fractures associated with the Emeishan basalt event, makes it recrystallized into medium-coarse crystal dolomite. With the intercrystalline pores and the residual vugs after the hydrothermal dissolution along the fractures, the high-quality intra-platform shoal-type thin-layer dolomite reservoirs are formed. The establishment of this reservoir formation model can provide important theoretical support for the sustainable development of Permian gas reservoirs in the Sichuan Basin.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
To analyze the episodic alteration of Middle Permian carbonate reservoirs by complex hydrothermal fluid in southwestern Sichuan Basin, petrology, geochemistry, fluid inclusion and U-Pb dating researches are conducted. The fractures and vugs of Middle Permian Qixia-Maokou formations are filled with multi-stage medium-coarse saddle dolomites and associated hydrothermal minerals, which indicates that the early limestone/dolomite episodic alteration was caused by the large-scale, high-temperature, deep magnesium-rich brine along flowing channels such as basement faults or associated fractures under the tectonic compression and napping during the Indosinian. The time of magnesium-rich hydrothermal activity was from the Middle Triassic to the Late Triassic. The siliceous and calcite fillings were triggered by hydrothermal alteration in the Middle and Late Yanshanian Movement and Himalayan Movement. Hydrothermal dolomitization is controlled by fault, hydrothermal property, flowing channel and surrounding rock lithology, which occur as equilibrium effect of porosity and permeability. The thick massive grainstone/dolomites were mainly altered by modification such as hydrothermal dolomitization/recrystallization, brecciation and fracture-vugs filling. Early thin-medium packstones were mainly altered by dissolution and infilling of fracturing, bedding dolomitization, dissolution and associated mineral fillings. The dissolved vugs and fractures are the main reservoir space under hydrothermal conditions, and the connection of dissolved vugs and network fractures is favorable for forming high-quality dolomite reservoir. Hydrothermal dolomite reservoirs are developed within a range of 1 km near faults, with a thickness of 30-60 m. Hydrothermal dolomite reservoirs with local connected pore/vugs and fractures have exploration potential.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Thin section and argon-ion polishing scanning electron microscope observations were used to analyze the sedimentary and diagenetic environments and main diagenesis of the Permian Fengcheng Formation shales in different depositional zones of Mahu Sag in the Junggar Basin, and to reconstruct their differential diagenetic evolutional processes. The diagenetic environment of shales in the lake-central zone kept alkaline, which mainly underwent the early stage (Ro<0.5%) dominated by the authigenesis of Na-carbonates and K-feldspar and the late stage (Ro>0.5%) dominated by the replacement of Na-carbonates by reedmergnerite. The shales from the marginal zone underwent a transition from weak alkaline to acidic diagenetic environments, with the early stage dominated by the authigenesis of Mg-bearing clay and silica and the late stage dominated by the dissolution of feldspar and carbonate minerals. The shales from the transitional zone also underwent a transition from an early alkaline diagenetic environment, evidenced by the formation of dolomite and zeolite, to a late acidic diagenetic environment, represented by the reedmergnerite replacement and silicification of feldspar and carbonate minerals. The differences in formation of authigenic minerals during early diagenetic stage determine the fracability of shales. The differences in dissolution of minerals during late diagenetic stage control the content of free shale oil. Dolomitic shale in the transitional zone and siltstone in the marginal zone have relatively high content of free shale oil and strong fracability, and are favorable “sweet spots” for shale oil exploitation and development.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
To clarify the formation and distribution of feldspar dissolution pores and predict the distribution of high-quality reservoir in gravity flow sandstone of the 7th member of Triassic Yanchang Formation (Chang 7 Member) in the Ordos Basin, thin sections, scanning electron microscopy, energy spectrum analysis, X-ray diffraction whole rock analysis, and dissolution experiments are employed in this study to investigate the characteristics and control factors of feldspar dissolution pores. The results show that: (1) Three types of diagenetic processes are observed in the feldspar of Chang 7 sandstone in the study area: secondary overgrowth of feldspar, replacement by clay and calcite, and dissolution of detrital feldspar. (2) The feldspar dissolution of Chang 7 tight sandstone is caused by organic acid, and is further affected by the type of feldspar, the degree of early feldspar alteration, and the buffering effect of mica debris on organic acid. (3) Feldspars have varying degrees of dissolution. Potassium feldspar is more susceptible to dissolution than plagioclase. Among potassium feldspar, orthoclase is more soluble than microcline, and unaltered feldspar is more soluble than early kaolinized or sericitized feldspar. (4) The dissolution experiment demonstrated that the presence of mica can hinder the dissolution of feldspar. Mica of the same mass has a significantly stronger capacity to consume organic acids than feldspar. (5) Dissolution pores in feldspar of Chang 7 Member are more abundant in areas with low mica content, and they improve the reservoir physical properties, while in areas with high mica content, the number of feldspar dissolution pores decreases significantly.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Taking the Lower Permian Fengcheng Formation shale in Mahu Sag of Junggar Basin, NW China, as an example, core observation, test analysis, geological analysis and numerical simulation were applied to identify the shale oil micro-migration phenomenon. The hydrocarbon micro-migration in shale oil was quantitatively evaluated and verified by a self-created hydrocarbon expulsion potential method, and the petroleum geological significance of shale oil micro-migration evaluation was determined. Results show that significant micro-migration can be recognized between the organic-rich lamina and organic-poor lamina. The organic-rich lamina has strong hydrocarbon generation ability. The heavy components of hydrocarbon preferentially retained by kerogen swelling or adsorption, while the light components of hydrocarbon were migrated and accumulated to the interbedded felsic or carbonate organic-poor laminae as free oil. About 69% of the Fengcheng Formation shale samples in Well MY1 exhibit hydrocarbon charging phenomenon, while 31% of those exhibit hydrocarbon expulsion phenomenon. The reliability of the micro-migration evaluation results was verified by combining the group components based on the geochromatography effect, two-dimension nuclear magnetic resonance analysis, and the geochemical behavior of inorganic manganese elements in the process of hydrocarbon migration. Micro-migration is a bridge connecting the hydrocarbon accumulation elements in shale formations, which reflects the whole process of shale oil generation, expulsion and accumulation, and controls the content and composition of shale oil. The identification and evaluation of shale oil micro-migration will provide new perspectives for dynamically differential enrichment mechanism of shale oil and establishing a “multi-peak model in oil generation” of shale.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the analysis of the fluid inclusion homogenization temperature and apatite fission track on the northern slope zone of the Bongor Basin in Chad, this paper studied the time and stages of hydrocarbon accumulation in the study area. The results show that: (1) The brine inclusions of the samples from the Kubla and Prosopis formations in the Lower Cretaceous coexisting with the hydrocarbon generally present two sets of peak ranges of homogenization temperature, with the peak ranges of low temperature and high temperature being 75-105 °C and 115-135 °C, respectively; (2) The samples from the Kubla and Prosopis formations have experienced five tectonic evolution stages, i.e., rapid subsidence in the Early Cretaceous, tectonic inversion in the Late Cretaceous, small subsidence in the Paleogene, uplift at the turn of the Paleogene and Neogene, and subsidence since the Miocene, in which the denudation thickness of the Late Cretaceous and after the turn of the Paleogene and Neogene are ~1.8 km and ~0.5 km, respectively. The cumulative denudation thickness of the two periods is about 2.3 km; (3) Using the brine inclusion homogenization temperature coexisting with the hydrocarbon as the capture temperature of the hydrocarbon, and combining with the apatite fission track thermal history modeling, the result shows that the Kubla and Prosopis formations in the Lower Cretaceous on the northern slope of the Bongor Basin have the same hydrocarbon accumulation time and stages, both of which have undergone two stages of hydrocarbon charging at 80-95 Ma and 65-80 Ma. The first stage of charging corresponds to the initial migration of hydrocarbon at the end of the Early Cretaceous rapid sedimentation, while the second stage of charging is in the stage of intense tectonic inversion in the Late Cretaceous.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
A seepage-geomechanical coupled embedded fracture flow model has been established for multi-field coupled simulation in tight oil reservoirs, revealing the patterns of change in pressure field, seepage field, and stress field after long-term water injection in tight oil reservoirs. Based on this, a technique for enhanced oil recovery (EOR) combining multi-field reconstruction and combination of displacement and imbibition in tight oil reservoirs has been proposed. The study shows that after long-term water flooding for tight oil development, the pressure diffusion range is limited, making it difficult to establish an effective displacement system. The variation in geostress exhibits diversity, with the change in horizontal minimum principal stress being greater than that in horizontal maximum principal stress, and the variation around the injection wells being more significant than that around the production wells. The deflection of geostress direction around injection wells is also large. The technology for EOR through multi-field reconstruction and combination of displacement and imbibition employs water injection wells converted to production and large-scale fracturing techniques to restructure the artificial fracture network system. Through a full lifecycle energy replenishment method of pre-fracturing energy supplementation, energy increase during fracturing, well soaking for energy storage, and combination of displacement and imbibition, it effectively addresses the issue of easy channeling of the injection medium and difficult energy replenishment after large-scale fracturing. By intensifying the imbibition effect through the coordination of multiple wells, it reconstructs the combined system of displacement and imbibition under a complex fracture network, transitioning from avoiding fractures to utilizing them, thereby improving microscopic sweep and oil displacement efficiencies. Field application in Block Yuan 284 of the Huaqing Oilfield in the Ordos Basin has demonstrated that this technology increases the recovery factor by 12 percentage points, enabling large scale and efficient development of tight oil.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
The miscibility of flue gas and different types of light oils is investigated through slender-tube miscible displacement experiment at high temperature and high pressure. Under the conditions of high temperature and high pressure, the miscible displacement of flue gas and light oil is possible. At the same temperature, there is a linear relationship between oil displacement efficiency and pressure. At the same pressure, the oil displacement efficiency increases gently and then rapidly to more than 90% to achieve miscible displacement with the increase of temperature. The rapid increase of oil displacement efficiency is closely related to the process that the light components of oil transit in phase state due to distillation with the rise of temperature. Moreover, at the same pressure, the lighter the oil, the lower the minimum miscibility temperature between flue gas and oil, which allows easier miscibility and ultimately better performance of thermal miscible flooding by air injection. The miscibility between flue gas and light oil at high temperature and high pressure is more typically characterized by phase transition at high temperature in supercritical state, and it is different from the contact extraction miscibility of CO2 under conventional high pressure conditions.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir, a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed, and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established. The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure. In the early stage of production or in areas far from the wellbore with high reservoir pressure, the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models. In the late stage of production or in areas close to the wellbore with low reservoir pressure, the condensate oil saturation can be calculated using the data of constant composition expansion test. In the middle stages of production or when reservoir pressure is at an intermediate level, the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure. Through simulation and field application, the new method is verified to be reliable and practical. It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Aiming at the problem that the data-driven automatic correlation methods which are difficult to adapt to the automatic correlation of oil-bearing strata with large changes in lateral sedimentary facies and strata thickness, an intelligent automatic correlation method of oil-bearing strata based on pattern constraints is formed. We propose to introduce knowledge-driven in automatic correlation of oil-bearing strata, constraining the correlation process by stratigraphic sedimentary patterns and improving the similarity measuring machine and conditional constraint dynamic time warping algorithm to automate the correlation of marker layers and the interfaces of each stratum. The application in Shishen 100 block in the Shinan Oilfield of the Bohai Bay Basin shows that the coincidence rate of the marker layers identified by this method is over 95.00%, and the average coincidence rate of identified oil-bearing strata reaches 90.02% compared to artificial correlation results, which is about 17 percentage points higher than that of the existing automatic correlation methods. The accuracy of the automatic correlation of oil-bearing strata has been effectively improved.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the tortuous capillary network model, the relationship between anisotropic permeability and rock normal strain, namely the anisotropic dynamic permeability model (ADPM), was derived and established. The model was verified using pore-scale flow simulation. The uniaxial strain process was calculated and the main factors affecting permeability changes in different directions in the deformation process were analyzed. In the process of uniaxial strain during the exploitation of layered oil and gas reservoirs, the effect of effective surface porosity on the permeability in all directions is consistent. With the decrease of effective surface porosity, the sensitivity of permeability to strain increases. The sensitivity of the permeability perpendicular to the direction of compression to the strain decreases with the increase of the tortuosity, while the sensitivity of the permeability in the direction of compression to the strain increases with the increase of the tortuosity. For layered reservoirs with the same initial tortuosity in all directions, the tortuosity plays a decisive role in the relative relationship between the variations of permeability in all directions during pressure drop. When the tortuosity is less than 1.6, the decrease rate of horizontal permeability is higher than that of vertical permeability, while the opposite is true when the tortuosity is greater than 1.6. This phenomenon cannot be represented by traditional dynamic permeability model. After the verification by experimental data of pore-scale simulation, the new model has high fitting accuracy and can effectively characterize the effects of deformation in different directions on the permeability in all directions.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the microfluidic technology, a microscopic visualization model was used to simulate the gas injection process in the initial construction stage and the bottom water invasion/gas injection process in the cyclical injection-production stage of the underground gas storage (UGS) rebuilt from water-invaded gas reservoirs. Through analysis of the gas-liquid contact stabilization mechanism, flow and occurrence, the optimal control method for lifecycle efficient operation of UGS was explored. The results show that in the initial construction stage of UGS, the action of gravity should be fully utilized by regulating the gas injection rate, so as to ensure the macroscopically stable migration of the gas-liquid contact, and greatly improve the gas sweeping capacity, providing a large pore space for gas storage in the subsequent cyclical injection-production stage. In the cyclical injection-production stage of UGS, a constant gas storage and production rate leads to a low pore space utilization. Gradually increasing the gas storage and production rate, that is, transitioning from small volume to large volume, can continuously break the hydraulic equilibrium of the remaining fluid in the porous media, which then expands the pore space and flow channels. This is conducive to the expansion of UGS capacity and efficiency for purpose of peak shaving and supply guarantee.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Based on the elastic theory of porous media, embedded discrete fracture model and finite volume method, and considering the micro-seepage mechanism of shale gas, a fully coupled seepage-geomechanical model suitable for fractured shale gas reservoirs is established, the optimization method of refracturing timing is proposed, and the influencing factors of refracturing timing are analyzed based on the data from shale gas well in Fuling of Sichuan Basin. The results show that due to the depletion of formation pressure, the percentage of the maximum horizontal principal stress reversal area in the total area increases and then decreases with time. The closer the area is to the hydraulic fracture, the shorter the time for the peak of the stress reversal area percentage curve to appear, and the shorter the time for the final zero return (to the initial state). The optimum time of refracturing is affected by matrix permeability, initial stress difference and natural fracture approach angle. The larger the matrix permeability and initial stress difference is, the shorter the time for stress reversal area percentage curve to reach peak and return to the initial state, and the earlier the time to take refracturing measures. The larger the natural fracture approach angle is, the more difficult it is for stress reversal to occur near the fracture, and the earlier the optimum refracturing time is. The more likely the stress reversal occurs at the far end of the artificial fracture, the later the optimal time of refracturing is. Reservoirs with low matrix permeability have a rapid decrease in single well productivity. To ensure economic efficiency, measures such as shut-in or gas injection can be taken to restore the stress, and refracturing can be implemented in advance.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
This work systematically reviews the complex mechanisms of CO2-water-rock interactions, microscopic simulations of reactive transport (dissolution, precipitation and precipitate migration) in porous media, and microscopic simulations of CO2-water-rock system. The work points out the key issues in current research and provides suggestions for future research. After injection of CO2 into underground reservoirs, not only conventional pressure-driven flow and mass transfer processes occur, but also special physicochemical phenomena like dissolution, precipitation, and precipitate migration. The coupling of these processes causes complex changes in permeability and porosity parameters of the porous media. Pore-scale microscopic flow simulations can provide detailed information within the three-dimensional pore and throat space and explicitly observe changes in the fluid-solid interfaces of porous media during reactions. At present, the research has limitations in the decoupling of complex mechanisms, characterization of differential multi-mineral reactions, precipitation generation mechanisms and characterization (crystal nucleation and mineral detachment), simulation methods for precipitation-fluid interaction, and coupling mechanisms of multiple physicochemical processes. In future studies, it is essential to innovate experimental methods to decouple “dissolution-precipitation-precipitate migration” processes, improve the accuracy of experimental testing of minerals geochemical reaction-related parameters, build reliable characterization of various precipitation types, establish precipitation-fluid interaction simulation methods, coordinate the boundary conditions of different physicochemical processes, and, finally, achieve coupled flow simulation of “dissolution-precipitation-precipitate migration” within CO2-water-rock systems.
Abstract (
)
Download PDF (
)
HTML
(
)
Knowledge map
Save
Foam stability tests were performed using sodium dodecyl sulfate (SDS) surfactant and SiO2 nanoparticles as foaming system at different asphaltene concentrations, and the half-life of CO2 foam was measured. The mechanism of foam stability reduction in the presence of asphaltene was analyzed by scanning electron microscope (SEM), UV adsorption spectrophotometric concentration measurement and Zeta potential measurement. When the mass ratio of synthetic oil to foam-formation suspension was 1:9 and the asphaltene mass fraction increased from 0 to 15%, the half-life of SDS-stabilized foams decreased from 751 s to 239 s, and the half-life of SDS/silica-stabilized foams decreased from 912 s to 298 s. When the mass ratio of synthetic oil to foam-formation suspension was 2:8 and the asphaltene mass fraction increased from 0 to 15%, the half-life of SDS-stabilized foams decreased from 526 s to 171 s, and the half-life of SDS/silica-stabilized foams decreased from 660 s to 205 s. In addition, due to asphaltene-SDS/silica interaction in the aqueous phase, the absolute value of Zeta potential decreases, and the surface charges of particles reduce, leading to the reduction of repulsive forces between two interfaces of thin liquid film, which in turn, damages the foam stability.
